The PK-5 includes over 90 of our best shop tools selected with versatility in mind. A great way to outfit a pro bench or to set up a dream home workshop. The PK-5 is an impressive, professional set of specialty tools that can help you perform hundreds of bicycle repair and maintenance procedures. An investment you'll use and appreciate for decades. Kit Includes: - ATD-1.2 Adjustable Torque Driver - AWS-1 Three-Way Hex Wrench Set: 4, 5, 6mm - AWS-3 Three-Way Hex Wrench Set: 2, 2.5, 3mm - BBT-10.2 Adjusting Cap Tool: For 8-Spline Hollowtech II - BBT-22 Bottom Bracket Tool - BBT-69.2 Bottom Bracket Tool - BO-2 Bottle Opener - CBW-1 Open End Wrench: 8/10mm - CBW-4 Open End Wrench: 9/11mm - CC-4 Chain Checker - CN-10 Professional Cable and Housing Cutter - CNW-2 Chainring Nut Wrench - CP-1.2 Cassette Pliers - CT-3.3 Chain Tool - CWP-7 Compact Universal Crank Puller - DAG-2.2 Derailleur Hanger Alignment Gauge - DH-1 Dummy Hub - DP-2 Threaded Dummy Pedal - DSD-2 Derailleur Screwdriver: Cross Tip - DSD-4 Derailleur Screwdriver: Flat Blade - DT-2 Rotor Truing Fork - FR-5.2H Cassette Lockring Tool with Handle - GSC-1 GearClean Brush - HMR-8 8 oz. Shop Hammer - HXS-1.2 Hex Wrench Set - MLP-1.2 Master Link Pliers - NP-6 Needle Nose Pliers - PAW-6 6" Adjustable Wrench - PH-1.2 P-Handle Hex Wrench Set - PW-4 Professional Pedal Wrench - RR-12 Tape Measure - SBC-1 Spoke, Bearing and Cotter Gauge - SBS-1.2 Socket and Bit Set - SCW-13 13mm Shop Cone Wrench - SCW-14 14mm Shop Cone Wrench - SCW-15 15mm Shop Cone Wrench - SCW-16 16mm Shop Cone Wrench - SCW-17 17mm Shop Cone Wrench - SCW-18 18mm Shop Cone Wrench - SCW-19 19mm Shop Cone Wrench - SP-7 Side Cutter Pliers - SW-0 Precision Spoke Wrench: .127" - SW-2 Precision Spoke Wrench: .136" - SWR-8 3/8" Drive Ratchet Handle - SZR-1 Shop Scissors - TL-1.2 Tire Lever Set - TL-4.2 Tire Lever Set - TL-6.2 Steel Core Tire Levers - TWS-1 Torx Compatible Wrench Set - UP-SET Utility Pick Set - VC-1 Valve Core Tool - ZP-5 5" Flush Cut Pliers
An expanded and evolved set of our finest professional level shop tools that addresses the changing tool demands of modern bikes and their mechanics. The PK-2 includes over 65 of our best tools and was put together with versatility in mind. A great way to outfit a pro bench, or to set up a fabulous home workshop, the PK-2 is an impressive set of tools that can help you perform hundreds of repairs and maintenance tasks.
Park Tool's Bottom Bracket Tapping & Facing Set is a precision tool system which provides a piloted means of tapping the threads in the bottom bracket shell of a frame. After tapping, the taps act as guides to keep the included facing cutter perfectly square with the axis of the bottom bracket for cleanup of the faces of the bottom bracket shell. The BTS-1 includes English taps, 1.370" x 24 TPI right hand thread for the adjustable cup, and 1.370" x 24 TPI left hand thread for the fixed cup. Italian thread taps, 36mm x 24 TPI right hand thread (Part #693) for the adjustable and fixed cups, are available as accessories.
Proper frame preparation is very important. Park Tool's Head Tube Reaming and Facing Set combines reaming and facing of the head tube to create a perfect fit for most sizes of head cups. Includes: • 30.1 mm reamer (part #751.2) and four different size pilots (29.8mm, 30.0mm, 33.8mm, and 36.8mm) • 690 facer • Quick-release, quick-adjust feature: bottom portion slides off and on easily without threading SHIS terminology: The HTR-1 as stock will face frames of EC29, EC30, EC34 and EC37. It will ream frames of EC30. Accessories will allow service in other standards.
Updated to fit an even wider range of hub, wheel and tire combinations with room to spare, utilizing a wider base structure and larger calipers. More accurate and easier to calibrate, the versatile TS-4.2 is solidly built to accurately self-center nearly any diameter wheel 16-inch to 29+ and any tire width up to 5-inches+. - Both uprights move simultaneously to always keep wheel centered in the stand - Accommodates tire widths up to 5-inches+ with or without brake rotor mounted - Speed knob to quickly change axle widths - Accommodates hub widths from 75mm to over 250mm - Precise operation and adjustability - Built in thru-axle adaptors - Machined, welded, assembled and calibrated in our factory in St. Paul, MN - Chrome plated and powder coated heavy gauge steel construction - Removable, replaceable nylon caliper tips to protect painted/anodized rims
The next generation of wheel truing stands! The TS-4 is made to accurately gauge any size wheel, with or without the tire installed. The TS-4 has many of the same features as Park Tool's famous TS-2.2 with some additional attributes to accommodate today’s wide variety of hub, wheel and tire combinations. - Both uprights move simultaneously to always keep wheel centered in the stand. - Accommodates axle widths from 75mm to 215mm - Direct action caliper arm adjusts to work with wheel sizes from 16" to 29"+ - Accommodates tire widths up to 5" with or without brake rotor mounted - Machined, welded, assembled and calibrated in our factory in St. Paul, MN - Precise accuracy, operation and adjustability - Built in thru-axle adaptors - Chrome plated and powder coated heavy gauge steel construction - Removable, replaceable nylon caliper tips to protect painted/anodized rims - Dial Indicator compatible (TS-2Di) (Sold separately) - Rotor gauge compatible (DT-3 & DT-3i.2) (Sold separately)
Park Tool put together this set of over 40 of their best tools to do basic maintenance and cleaning tasks as well as perform a wide variety of repairs and adjustments on just about any bicycle. A perfect way to start or add to your collection of shop quality bicycle tools. The AK-4 includes a tough toolbox to protect your investment. Kit Includes: - ATD-1.2 Adjustable Torque Driver - BO-2 Bottle Opener - CC-4 Chain Checker - CM-5.2 Cyclone Chain Scrubber - CN-10 Professional Cable and Housing Cutter - CNW-2 Chainring Nut Wrench - CT-3.3 Chain Tool - DCW-1 Double-Ended Cone Wrench: 13/14mm - DCW-2 Double-Ended Cone Wrench: 15/16mm - DCW-3 Double-Ended Cone Wrench: 17/18mm - FR-5.2 Cassette Lockring Tool - GP-2 Pre-Glued Super Patch Kit - GSC-1 GearClean Brush - HXS-1.2 Professional L-Shaped Hex Wrench Set - MLP-1.2 Master Link Pliers - PAW-12 12" Adjustable Wrench - PW-5 Home Mechanic Pedal Wrench - RR-12 Tape Measure - SD-2 #2 Phillips Screwdriver - SD-3 3mm Flat Blade Screwdriver - SR-12.2 Sprocket Remover / Chain Whip: 5 to 12-Speed Compatible - SW-0 Precision Spoke Wrench: .127" - SW-2 Precision Spoke Wrench: .136" - TB-2 Emergency Tire Boots - TL-1.2 Tire Lever Set - TWS-3 Torx Compatible 3-Way Wrench - VC-1 Valve Core Tool
Park Tool's Fork Threading Set is designed for cutting new threads and for chasing existing threads on fork columns that are not chromed. The FTS-1's expandable cutting dies are made from the highest quality high-speed steel for precision cutting and long life. The unique thread guide system used with the FTS-1 is specially designed to allow the metal chips and shavings that result during use to fall completely through the guide, preventing damage to the fork threads and the tool. The FTS-1 includes: • Die handles • 1" x 24 tpi cutting die (Part #606) • 1" cutting guide (Part #610) Accessory dies and guides are also available separately: • 1-1/8" x 26 die (Part #607) • 1-1/8" guide (Part #611) • 1-1/4" x 26 die (Part #608) • 1-1/4" guide (Part #612) Die handles fit all three sizes of dies and guides.
- Used to ream and face BB86/92 bottom bracket shells to an ID of 40.98mm - Used in conjunction with HTR-1 head tube reaming and facing set (PK-6710), 750.2 centering cone adapter (PK-6735) and 690-XL facing cutter (PK-6730)
The 37-piece SBS-3 from Park Tool is a comprehensive, shop-quality set of sockets, hex bits, and Torx compatible drivers selected specifically to tackle a wide variety of common bike repair needs. The SBS-3 also includes flat-faced sockets in common sizes for work on suspension forks. Ideal for use with Park Tool torque wrenches, the 3/8" drive bits and sockets are forged from tough, chrome vanadium steel and nickel chrome plated for lasting durability.
Park Tool has long provided some of the best cutting and machining tools in the bicycle industry. Their 690 Cutting Facers reflect their commitment to maintaining this high level of quality. Please read below for use and compatibility information specific to each size cutter: - 45mm (690): The 690 cutting facer is used on the HTR-1, HTR-1B, BFS-1, and BTS-1 cutting and facing tools. The facer has an outside diameter of approximately 45mm. - 57mm (690XL): The 690-XL is a larger version of the 690 facer for the HTR-1 Head Tube Reamer and Facer. It has a nominal outside diameter of 57mm. It may be used in conjunction with the 788 reamer. It is also used with the 767 Pilot or the 768 Pilot to face only the large diameter headtubes used with, "low profile," ZS-type headsets. - 65mm (690-XXL): The 690-XXL faces large headtubes. It has a nominal outside diameter of 65mm. Use the 690-XXL facer with the 750.2 Centering Cone Adaptor and 789 Reamer or 790 Pilot when facing head tubes with internal diameters of 55.95–55.90mm.
World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. The MWR-SET includes 6mm to 17mm wrenches with a 12-point two-way ratcheting box end. Forged from chrome vanadium steel, chrome-plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip. Strong, comfortable, and beautiful! - Includes 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, and 17mm wrenches
With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The TW-6.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). Designed for higher torque settings for repairs and installation in the bottom bracket, cassette lockring and other areas that use a higher torque settings. For lower torque setting, see the TW-5. Comes with its own protective case. - 10–60 Newton meter range (88–530 Inch Pounds) - Adjustable in 0.25 Nm increments - Ratcheting 3/8" drive - Reads and registers for both left hand and right hand threading - Dial-adjust system allows desired torque setting to be preset - Calibrated to be accurate to +/- 4% - Length: 36.2cm (14.25")
Improperly aligned frame or fork dropouts can cause bent axles and quick-release skewers, as well as tracking and shifting problems. The Frame and Fork End Alignment Gauge Set quickly determines whether the frame or fork dropouts are aligned and parallel. If an error is detected, long handles and comfortable molded grips afford plenty of leverage for straightening. These Park gauges adjust to compensate for various hub widths from 100mm to 160mm, too.
With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The Park Tool TW-5.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). With a range of 2-14Nm, the TW-5.2 is designed for the lower torque settings that a shop or consumer would use for proper seat post, seat clamp and handlebar / stem applications. Comes with its own protective case.
No more need to hold wheels between your knees, balance on a bench top or ask for help. The WH-1 Wheel Holder firmly holds thru axle and quick release wheels at three convenient positions. It’s like having a strong helper to hold wheels during cleaning, tire and tube work, hub work, cassette work, and tubeless installation. The WH-1 can be bolted or clamped directly to a bench or installed in a bench vise. Uses and Features: - Quick and easy access to hold virtually any wheel to perfectly position your work for a variety of tasks including but not limited to: - Wheel building -Cassette removal and installation - Tire and tube removal and installation - Tubeless tire work - General cleaning - Hub work - Holds wheel at vertical, 35 degrees from vertical, and horizontal positions - Accepts 12, 15, and 20mm thru axles and 5mm skewers - E-Nickel finish for durability
The CRS-15.2 uses two different insert rings to install bearing races on the 1.5-inch and 1-1/4-inch forks. The bearing surface is spared a direct hit by using aluminum inserts. Using a hammer, tap firmly on the end cap of the tube and seat the race into its proper place safely and accurately. Included extension allows work on fork steering tubes up to 425mm. - SHIS terminology: The CRS-15 services crown races in SHIS 33 and 40.
A daily-use, shop version of Park Tool's world-famous CM-5.2 Chain Scrubber. The CM-25 features a super-tough die-cast aluminum case and handle, plus a unique brush/sponge replacement cartridge that makes it easy to keep it running smoothly and working properly. Park Tool's proven four-sided scrubbing action makes thoroughly cleaning chains quick and easy. A shop quality cleaner built to give years of constant use. - Proven chain scrubbing technology leaves chains sparkling clean - Durable A380 aluminum die cast case and removable handle - Dual-sided sponges and wicking pads to help reduce drips - Rotating brushes clean on all four sides of every link - Brush and sponge cartridge quickly and easily clicks in and out (RBS-25) - Locking cover with stainless steel hinge pins - Choose drip or immersion fluid application methods - 100% serviceable
Quickly, safely and easily set your crown race on 1.5-inch steerer tubes with Park's CRS-15 Crown Race Setting System. Specifically engineered for oversized steerers, the CRS-15 comes with one setting tube and a 1.5-inch inset that ensures full contact with the crown race for precision installation.
Engineered for fit, function, and leverage, these L-shaped shop-quality hex wrenches are a must have for every workshop. - High-torque, industrial steel wrenches - Straight hex shaft on the short side, ball end on the long side - Includes 2, 2.5, 3, 4, 5, 6, 8, and 10mm - Comfortable, ergonomically designed nylon handles fit perfectly in your hand - Durable wall/pegboard mount tool holder allows easy access and organization
The key to wheels that are strong and reliable is having spokes that are properly and uniformly tensioned. Park's Spoke Tension Meter accurately and reliably measures the absolute tension of each of the spokes in a wheel, as well as the relative tension between all the spokes in a wheel. It's easy to use, affordable and it works on nearly any bicycle spoke, no matter its diameter, material or shape.
The DAG-2.2 is an indispensable shop tool that can be used to both measure and straighten misaligned derailleur hangers solving a high percentage of shifting problems. - Gauge bar made of heavy gauge, chrome plated steel - Adjusts to fit 20" to 29"+ wheels - Replaceable threaded tip - Upgraded large inner shaft for added strength* - Tighter tolerances for improved accuracy* - Improved clearance and reach to fit more frame/hanger combos including low clearance thru-axle derailleur hangers* *Compared to DAG-2
Park Shop Cone Wrenches are made of thin tool steel to fit the low-clearance adjusting nuts and cone flats on hubs and other bearing assemblies. Their special Y-heads put more material where it's needed for greater strength. Most applications require several cone wrenches, so Park gives you a whole set, featuring 13mm - 24mm, 26mm and 28mm wrenches to suit your repair needs.
Engineered for fit, function, and leverage, these L-shaped shop-quality Torx compatible wrenches are a must have for every workshop. - High-torque, industrial steel wrenches - Torx compatible drivers at each end - Includes T6, T8, T10, T15, T20, T25, T30, and T40 - Comfortable, ergonomically designed nylon handles fit perfectly in your hand - Durable wall/pegboard mount tool holder allows easy access and organization
Shop-quality, adjustable torque driver that limits torque applied to fasteners, preventing over-tightening and damage to lightweight components. The ATD-1.2 features all-metal internal construction with a comfortable, ergonomic composite molded grip. Each tool is assembled and calibrated at Park Tool's factory in Minnesota.
What's your seatpost size again? Park's Digital Caliper accurately measures seatposts, head tubes, bearings, spoke diameters, etc. It's a precision instrument built accurate to 0.01mm with a stainless-steel mechanisms and a rugged composite body. The tool’s ability to measure in metric, decimal inch, and fractional inch makes it an indispensable home workshop tool. It features an automatic shut-off and comes with a protective sleeve and the battery.
Take the guesswork out of installing cables, wires and housing inside the frame. The IR-1.2 speeds the internal frame routing of electric wires, shift cable/housing, brake cable/housing and hydraulic tubing on carbon fiber, titanium, and aluminum frames. Kit includes four plastic-coated 250cm cables with attached magnets and unique fittings plus an external guide magnet to speed operation. Newly updated to include a dedicated E-tube Di2 cable connector that easily pulls through a 6mm frame hole. Opposite polarity magnets on cables seek and attach inside frame tubes, making it easy to route through frame entrances and exits. Works with any size frame including tandems. A true time and frustration saver!
Park's Master Chain Tool is designed specifically to work with the tight tolerances and narrow profiles of 10- and 11-speed chains and all high-quality derailleur chains. It's made of tool steel for excellent durability and uses an integrated link pocket to ensure precise alignment. It also features perfectly contoured, cushioned handles for comfort and ease of use. This pro-level chain tool includes a removable anvil to peen Campagnolo 11-speed chains. (The CT-4.3 is not compatible with Wipperman chains.)
Park Tool's Thru Axle Adaptors make it possible to adapt all Park Tool Truing Stands to work with 12mm, 15mm, 20mm, and 25mm thru axle front wheels, as well as Cannondale Lefty wheels (each sold separately). The TS-TA also work with the rear 135mm thru axle hubs in the TS-2.2 and TS-3. The TS-TA when used in the TS-8, TS-25, TS-15, TS-7 or TS-5 will work with all rear thru axle hubs. For thru axle hubs greater than 135 (142, 150, 157, etc.) in the TS-2.2, use the TS-2TA Thru Axle Adaptors (sold separately).
Park's Torx Wrench Set includes T-handled T6, T8, T10, T15, T20, T25, T30 and T40 Torx wrenches with offset handles made from durable nylon in a comfortable, ergonomic design. The wrenches are made of high-torque industrial steel for exceptional durability. Plus, this set of super tools comes with a wall mount for easy access.
Page 1 of 7 Next page