Parts & Accessories

The Fat Conversion Rear hub provides the ultimate in fatbike hub versatility by allowing hub conversion between quick-releases and thru-axles. 170/177mm features - Convertible 10 x 170mm QR/12 x 177mm Thru-Axle spacing - Four sealed cartridge bearings - Serviceable three-pawl freehub mechanism - 58mm flange diameter, right center to flange: 37mm, left center to flange: 44mm - Thru Axle and Q/R Conversion end caps included - 170mm Flip-Off skewers included - XD freehub and conversion caps also available separately 190/197mm features - Convertible 10 x 190mm QR/12 x 197mm Thru-Axle spacing - Four sealed cartridge bearings - Serviceable three-pawl freehub mechanism - Thru Axle and Q/R Conversion end caps included - Flip-Off skewer not included - 422 grams

This conversion kit allows you to use SRAM's 11-speed mountain cassette on your Stan's NoTubes wheels. Each kit includes an XD freehub, spacer, drive side end cap, and three sealed bearings.

Secure your wheels with tough and light Titanium Quick Release skewers from Zipp. They are sized perfectly for your road bike and they flip easily for quick wheel mounting and unmounting.

Get rolling again with a replacement 10-speed freehub body for Mavic wheels.

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

Our Trainer Axle is designed to adapt your Surly MDS/Gnot Boost thru-axle-equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - This axle is for Surly bikes with the MDS/Gnot Boost system. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum, and hard-anodized for rugged durability. - No special tools required. Design allows for wheel installation or removal using your standard 5 mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

Whisky’s tubeless rim tape is designed to make setup as easy as possible. Elasticity allows for smooth, even adherence while translucency lets you see where the tape contacts the rim. Different widths available to fit almost any rim.

Your riding doesn’t need to stop when the weather gets cold. Features - Giant road thru-axle trainer axle - Alloy construction - For use on 2017+ Giant road bikes with a 142x12mm rear thru-axle

On today's MTB frames, there are many dropout diameter and width standards. Most Mavic wheels can be fitted with specific adapters to match your wheelset with your frame. - Converts Crossmax rear wheels from 135mm to 142mm spacing - One pair required for each hub to be converted

- Cassette Body Type: Shimano/SRAM 11 Speed Road - Material: Steel

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many BMX hubs - Type: Solid Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 187mm - 1 axle per bag

• 5-sided key locking skewer set • Chromoly axles • 6061 anodized aluminum • Includes seat and F+R wheel skewers • 95g (set)

The Problem Solvers Downtube Shift Cable Adjusters replace your existing shift adjusters, or let you add integrated shifters to your current down tube shifter-equipped road bike. Made from durable plastic and stainless steel, these adjusters are built to last for countless miles on your road steed.

Stan's Downhill Rim Strip converts standard tubed wheels to tubeless so you can reap the benefits. Going tubeless allows you to run low tire pressure for better traction while drastically reducing the chances of a flat. Stan's rim strips create a tight seal with the tire bead, reducing the instances of "burping". Plus, you won't miss dealing with flat tires and you'll save money on tubes!

WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 46mm

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

Designed with today’s taller, double-digit cog stacks in mind, Chris King's R45 cassette lock rings feature longer threads to provide secure engagement with the hub driveshell. A Chris King cassette lock ring is the perfect complement to any Chris King hub, or for anyone looking to add a dash of King performance to other manufacturer’s compatible rear hubs. They are available for both 11 and 12 tooth small cogs, as well as Shimano or Campagnolo hubs.

Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.

WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 34mm

Shimano XT M8000 quick release skewer.

Features - Strong nylon reinforced material handles high-pressures - Adhesive backed for a secure fit - Does not rot - 0.5mm thick

Features - Strong nylon reinforced material handles high-pressures - Adhesive backed for a secure fit - Does not rot - 0.5mm thick

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

Shimano Nexus and Alfine Internally Geared Hub Cassette Joints - Shimano model # CJ-S700 - Does not include cable fixing bolt unit - OEM cassette joint unit for Alfine SG-S700

Whisky Parts Co. Tubeless Rim Tape.

Shimano Nexus and Alfine Internally Geared Hub Cassette Joints - Shimano model # CJ-S7000 - Does not include cable fixing bolt unit - OEM cassette joint unit for Alfine SG-S7000-8

Add an Alfine hub, cog, spokes, and a rim to this Shimano Internally Geared Hub Small Parts Kit, and you're ready to rock. - Alfine hubs are packaged without small parts and require this kit plus a cog - Nexus hubs are packaged with small parts and cogs and do not require an additional small parts kit - For 11-Speed Hub - Includes CJ-S700 Cassette Joint for Vertical Dropouts *Cassette joint does not fit Di2 Alfine hubs

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: JoyTech 9mm x 1, front "parallax" style hub - Compatible with 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 15.0mm - Length: 11.0mm - 1 cone per bag COMPATIBLE HUBS: - JoyTech 9mm x 1, front "parallax" style hub - Taiwanese hubs with 9mm x 1 axle

-Replacement left side cone and locknut for Shimano 105 FH-5800 rear hub

The kit contains 3 pawls and 3 springs. Compatible with all Stan's Hubs. Very durable and with normal uses will last the life of the hub.